Classic SeaCraft Community  

Go Back   Classic SeaCraft Community > General Discussion > Performance
FAQ Community Calendar Today's Posts Search

Notices

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 12-29-2010, 10:55 AM
DANNY18SC DANNY18SC is offline
Junior Member
 
Join Date: Dec 2010
Location: Tallahassee, FL
Posts: 16
Default johnson commercial 155

has anyone ever had any experiences, good or bad, with these motors? the guy said he just had it rebuilt and hasnt even broken it in yet. would this be too much for my 78 18ft? this might be a deal i cant pass up, but dont want a motor with alot of headaches.
__________________
78 18'
89 200 Yamaha
http://i1215.photobucket.com/albums/...1227/boat4.jpg
Reply With Quote
  #2  
Old 12-29-2010, 11:57 PM
Fr. Frank Fr. Frank is offline
Senior Member
 
Join Date: Oct 2003
Location: Shalimar, Florida
Posts: 2,265
Default Re: johnson commercial 155

What year? With or without the VRO system?
__________________
Common Sense is learning from your mistakes. Wisdom is learning from the other guy's mistakes.

Fr. Frank says:
Jesus liked fishing, too. He even walked on water to get to the boat!

Currently without a SeaCraft
(2) Pompano 12' fishing kayaks
'73 Cobia 18' prototype "Casting Skiff", 70hp Mercury
Reply With Quote
  #3  
Old 12-30-2010, 01:25 AM
workinpr0gress workinpr0gress is offline
Senior Member
 
Join Date: Jun 2009
Posts: 601
Default Re: johnson commercial 155

Low compression motor, they run on the worst of fuel. I forget the octane they can run on. Good smokey old motor, they were the predominant motor on the back of towboats for years. 155 I think was basically a 185, bigger lower, couple other things.
__________________
Thank goodness that in the scheme of things you are broke, powerlesss and inconsequential, because with the shortsighted alternatives and idealogy you have you'd be much worse than those you complain about.
Reply With Quote
  #4  
Old 12-30-2010, 03:59 PM
DANNY18SC DANNY18SC is offline
Junior Member
 
Join Date: Dec 2010
Location: Tallahassee, FL
Posts: 16
Default Re: johnson commercial 155

89 motor. the guy said the VRO was disabled, if it isnt and i get it, i will disable it and mix my gas. do you think this wee be too much weight for my 18? i looked it up on NADA, says it weight 400 lbs. being a low comression motor, what #s do i need to look for on a comp gauge?
__________________
78 18'
89 200 Yamaha
http://i1215.photobucket.com/albums/...1227/boat4.jpg
Reply With Quote
  #5  
Old 12-30-2010, 07:13 PM
DonV DonV is offline
Senior Member
 
Join Date: Jul 2004
Location: Apollo Beach or Islamorada
Posts: 3,488
Send a message via ICQ to DonV
Default Re: johnson commercial 155

I just sold a boat with a 1989 150hp Johnson "cross-fire" motor (not a looper). I've had four of these type engines and they never broke, just wore out. I thought the 88hp, 155hp commercial marketed motors were mix your oil only type engines. That way, no worry of VRO failures.
Reply With Quote
  #6  
Old 12-30-2010, 07:31 PM
Old'sCool Old'sCool is offline
Senior Member
 
Join Date: Jun 2006
Location: Charleston, SC
Posts: 2,122
Default Re: johnson commercial 155

My '90 88 SPL's were mix your own.
Reply With Quote
  #7  
Old 12-30-2010, 11:24 PM
seacraftks seacraftks is offline
Senior Member
 
Join Date: Nov 2010
Location: Maine
Posts: 134
Default Re: johnson commercial 155

a 155 cant say i ever recall seeing one
Reply With Quote
  #8  
Old 12-31-2010, 11:40 AM
pelican pelican is offline
Senior Member
 
Join Date: Apr 2010
Location: cape may nj
Posts: 596
Default Re: johnson commercial 155

Quote:
I just sold a boat with a 1989 150hp Johnson "cross-fire" motor (not a looper). I've had four of these type engines and they never broke, just wore out. I thought the 88hp, 155hp commercial marketed motors were mix your oil only type engines. That way, no worry of VRO failures.
you're correct...the spl's and commercial engines,had no oil injection...

also,"low compression engines" ? it's a 2 stroke,the compession ,ratio is much less than a 4 stroke engine...that comment concerning "it's a low compression engine",it's incorrect...
__________________
do not let common sense get in your way
Reply With Quote
  #9  
Old 12-31-2010, 01:30 PM
workinpr0gress workinpr0gress is offline
Senior Member
 
Join Date: Jun 2009
Posts: 601
Default Re: johnson commercial 155

They don't run a different cylinder head on those than other crossflows?
__________________
Thank goodness that in the scheme of things you are broke, powerlesss and inconsequential, because with the shortsighted alternatives and idealogy you have you'd be much worse than those you complain about.
Reply With Quote
  #10  
Old 01-01-2011, 02:35 PM
CaptMick CaptMick is offline
Senior Member
 
Join Date: Apr 2010
Location: Hilton Head Island, SC
Posts: 204
Default Re: johnson commercial 155

Quote:
89 motor. the guy said the VRO was disabled, if it isnt and i get it, i will disable it and mix my gas. do you think this wee be too much weight for my 18? i looked it up on NADA, says it weight 400 lbs. being a low comression motor, what #s do i need to look for on a comp gauge?
For what its worth I have a 417 pound 150 Merc on my 18 without any changes to scuppers or deck and I am fine. Hull is an 85.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:14 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
All original content © 2003-2013 ClassicSeacraft