Classic SeaCraft Community  

Go Back   Classic SeaCraft Community > General Discussion > Repairs/Mods.
FAQ Community Calendar Today's Posts Search

Notices

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 08-02-2010, 02:28 AM
CaptCurt CaptCurt is offline
Member
 
Join Date: Feb 2010
Location: Houston, TX
Posts: 52
Default Motor problem on maiden voyage

So I put her in the water for the first time on Saturday. At first the motor wouldn't pee... but I ran a piece of wire leader up the pee hole and cleared out some trash. After that it worked fine.

The big issue started after I got past the no-wake zone and gave her the gas. Up to 1/4 throttle it worked fine. Beyond that, a big vibration started.... almost like heavy cavitation (but I don't think it was cavitation). It would never really rev up above about 2200 RPM. I went to half and then full throttle and it just vibrated and wouldn't pick up steam. I ended up turning around and (after waiting in line for 45 minutes at the ramp) putting her back on the trailer.

Once we got back home, I hooked up the water hose and ran it. There was no vibration, but the motor never really seemed to produce power beyond 1/4 to 1/3 throttle. It just doesn't rev.

Also, it started giving me some kind of audible alarm, only when giving medium to full throttle. Not sure if it a low fuel flow alarm or what.

The motor is a 2000 Suzuki DT140 fuel injected/oil injected 2-stroke. The fuel tank, fuel lines, fuel filter are all new. It has fresh gas.

I was thinking that maybe the filter located at the reservoir near the fuel injection system is clogged. I haven't had a chance to open it up yet.

Ideas? I sure am frustrated!
__________________
Working on my first project!
1979 20' Master Angler
Suzuki DT140
Reply With Quote
  #2  
Old 08-03-2010, 10:12 PM
Bushwacker Bushwacker is offline
Senior Member
 
Join Date: Feb 2007
Location: N. Palm Beach, Fl.
Posts: 2,456
Default Re: Motor problem on maiden voyage

Sounds like it's running on 3 cylinders, classic misfire under load. Maybe a bad coil. Pull the plugs and look for one that's black/heavily oil fouled, then check spark on that cyl. while cranking. Spark should jump about a 1/2" gap (don't hold on to the wire while doing that! )
__________________
'72 SeaFari/150E-Tec/Hermco Bracket, owned since 1975.
http://i188.photobucket.com/albums/z...Part2019-1.jpg
Reply With Quote
  #3  
Old 08-04-2010, 05:51 PM
eggsuckindog eggsuckindog is offline
Senior Member
 
Join Date: Mar 2003
Location: Tampa
Posts: 2,354
Default Re: Motor problem on maiden voyage

Quote:
Sounds like it's running on 3 cylinders, classic misfire under load. Maybe a bad coil. Pull the plugs and look for one that's black/heavily oil fouled, then check spark on that cyl. while cranking. Spark should jump about a 1/2" gap (don't hold on to the wire while doing that! )
good start and as mentioned you'll only hold that wire once
__________________
Any way you measure it - dumbass is expensive
Reply With Quote
  #4  
Old 08-04-2010, 09:45 PM
DanH DanH is offline
Junior Member
 
Join Date: Aug 2010
Location: Brewster
Posts: 6
Default Re: Motor problem on maiden voyage

I believe the trouble you are having is over heating.The audible is part of the safe system.Check your thermostats,water pump and make sure it pees like an 18 year old.g
Good luck.
__________________
Pats Fan
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:37 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
All original content © 2003-2013 ClassicSeacraft