Classic SeaCraft Community  

Go Back   Classic SeaCraft Community > General Discussion > Repairs/Mods.

Notices

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 12-10-2010, 05:07 PM
copout copout is offline
Senior Member
 
Join Date: Nov 2009
Location: Davie, Fl
Posts: 171
Default Cleaning fuel tanks?

Here's what I got!
One polly tank below deck.
One aluminum tank above deck but below console.
Neither can be removed without major mods.
I have removed all fuel. The bottom tank was BAD, tar/varnish residue on the bottom.

Plan of attack!?!
Flush with water/degreaser?
Flush with staight water.
Remove water.
Rinse with Iso-alcohol, them pump that out & then vent/run blower to evap remaining Iso?
Complete with new lines, spliter valve & hardware.
I am open to suggestions.


Top tank



Bottom tank



Reply With Quote
  #2  
Old 12-11-2010, 02:03 PM
Blue_Heron Blue_Heron is offline
Senior Member
 
Join Date: Jan 2006
Location: Gator Country
Posts: 1,416
Default Re: Cleaning fuel tanks?

I wish you luck, but if you can remove varnish from fuel tanks, without removing them, with detergents, degreaser, or solvents, you’ll be my new hero. I didn’t try alcohol, but I did try lacquer thinner and acetone. They removed the soluble constituents, but left a crust behind. I put acetone, lacquer thinner and marbles in my tanks and carried them around in the back of my truck for a few weeks. The marbles knocked loose some of the solids. After siphoning out the solvent and cleaning with detergent, this is what came out:




Ultimately, I had to invent the Tank Tumbler TM to get the last of the varnish.



Like I said, I wish you luck, but I think you’re going to have to pull the tanks to get the varnish out.

Dave

P.S. That was a nice post about the family history behind your boat. You done good.
__________________
Blue Heron Boat Works
Reinventing the wheel, one spoke at a time.
Reply With Quote
  #3  
Old 12-11-2010, 05:48 PM
copout copout is offline
Senior Member
 
Join Date: Nov 2009
Location: Davie, Fl
Posts: 171
Default Re: Cleaning fuel tanks?

Thanks blue! I'll now only need it for the bottom tank. That's if I really need the extra fuel! Fumes are getting to my brain but VICTORY sure feels good!
I'm gonna need some help with sealing the console back down? Bring on the old, I mean wise salts!


Reply With Quote
  #4  
Old 12-12-2010, 06:48 AM
FELLOW-SHIP FELLOW-SHIP is offline
Senior Member
 
Join Date: Feb 2002
Location: Cooper City, Fl
Posts: 1,798
Default Re: Cleaning fuel tanks?

Hi Copout:


I did not try to repair my old tank I replaced it so I really did not have to face your problems but I didn’t have a choice. Your aluminum tank looks like you could save it and the poly tank should be able to save as well.
I agree with Blue Heron you probably need to pull both to work on them and use all the chemicals he did as well. On the aluminum tank you might consider paint thinner or a oven cleaner as well. I would take some samples of the junk and test them with both to see if they will break down the varnish.
It looks like to me the aluminum tank has no baffles in it so you might be able to do one more thing Blue Heron did not try a commercial pressure washer running it through all the access holes and trying to strip away all the varnish.

On the poly tank you might be able to use a rubber hammer to tap on the outside of the tank to help break up the varnish then use the pressure washer but I would be careful with the chemicals in it. Do some testing on the outside of the tank before you put anything on the inside to see how it reacts.

Make sure you pull the fuel sending devices first and remove all rubber gaskets that might be present.

After its all over make sure you invest in a Racor fuel filter with the see through plastic piece and drain in the bottom so you can see what’s going on. There is only one thing worse that pulling the tanks and cleaning them and that is destroying your motor because crap got into the engine and not it needs a rebuild.

Don’t you just love Ethanol it brings new meaning to the word S**T.





FellowShip

………………………….

Just for the Grins

Official 23’ SF Antique Classic SeaCraft Owner
Reply With Quote
  #5  
Old 12-18-2010, 09:37 AM
tgilchrist01 tgilchrist01 is offline
Junior Member
 
Join Date: Dec 2008
Location: Snug Harbor RI
Posts: 27
Default Re: Cleaning fuel tanks?

Copout,
One of the pictures above, shows a flange that holds your sending unit and pickup tube. I'm making a new tank for my boat this year and interested in that setup. Does it have a manufacture's name one it?

Tom
Reply With Quote
  #6  
Old 12-18-2010, 10:50 AM
copout copout is offline
Senior Member
 
Join Date: Nov 2009
Location: Davie, Fl
Posts: 171
Default Re: Cleaning fuel tanks?

Tom, that flange is on a poly tank. I believe it's OEM from Kracor tanks.
http://4wings.com/lib/files/fueltanks.pdf
Based on measurements I have model 88-7059 seen down on page 9. I will be looking to replace the gasket, so when I contact them I can ask about replacement flanges for you.

Ryan
Reply With Quote
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:19 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
All original content © 2003-2013 ClassicSeacraft